СЕКРЕТЫ СОТОВЫХ ТЕЛЕФОНОВ Ericsson 388 *#06# for checking the IMEI (International Mobile Equipment Identity) *#0000# to reset the phones menu-language to English. >*<<*<* for checking the firmware revision information (software release) >*<<*<*> 1-row text strings. if pressing yes you can check the phones text programming in currently selected language. (298 entries) >*<<*<*>> n-row text strings. if pressing yes you can check the phones text programming in currently selected language. (160 entries?) Ericsson DH-3xx/vi Secret Codes 923885[Menu] --- NAM programming 904060[Menu] --- Reset phone 904080[Menu] --- Title blink 904090[Menu] --- TestMode on/off 904059[Menu] - Test Set (commands) (0..9=0..9 *=A; #=B; clr=C; menu=D; no=E; rcl=F). press Yes, at the @ enter the command. some of the commands have parameters of different lenght. if one parameter doesnt work try another. Ericsson GF768 Редактирование приветствия 1. Войдите в Keylock меню. 2. Установите блокировку в Auto. 3. Нажмите YES затем удерживайте Левую стрелку пока не появится Greetings меню. GF788 меню в вашем GF768 телефоне! (1) 1. Войдите в EDIT Меню и нажмите YES. 2. Нажмите число "2" затем YES. 3. В "NAME" удерживайте клавишу "2" пока не появится число "2". Нажмите YES. 4. Нажмите YES еще раз (для сохранения позиции ) затем БЫСТРОнажмите и удерживайте левую стрелку пока на дисплее не появится "SIZE". 5.Нажмите YES и выберите "Full size". Теперь у вас будет меню как и в GF788 . GF788 меню в вашем GF768 телефоне! (2) 1.Войдите в MissedCall 2. Очистите список 3. Нажмите Правую стрелку -> на пару секунд 4. Появится SIZE меню 5. Выберете YES и выйдете от туда Примечание . Данный код работает с версией 990122. GF788 меню в вашем GF768 телефоне! (3) 1. Войдите и установите громкость звонка и нажмите YES. 2. Когда 'STORED' появится - удерживайте нажатой правую стрелку пока на экране не появится 'Extended Menu' 3. Выберете "Activate" в меню Примечание . Данный код работает с версией 980910 Ericsson KF-768/788 Secret Codes 923885[Menu] --- NAM programming 904060[Menu] --- Reset phone 904080[Menu] --- Title blink 904090[Menu] --- TestMode on/off 904059[Menu] --- Test Set Known commands: (dunno what the data's say) 1F Mode Set 2F Mode Set 27 Some Data (2*param=00..99) 28 Some Data (4*param=00..FF) 38 Many Data 3A Some Data 3C Set Channel Number (in mode 1F) (4*param=0001..1023) 3D Show RX Level 3F Reboot 4F Exit 5F Some Data (XXXXXXXXXXh) 63 Some Data (XXXX) 73 Copyright 83 Set Channel Number (in mode 1F) (4*param=?001..?31F) 85 Speaker Off (in mode 1F) 86 Speaker On (in mode 1F) 8B Show TX Level 94 Many Data 95 Some Data (XXXXh) 96 ESN num in hex (XXh-XXXXXXh) AA Tone (in mode 2F) (2*param=00..FF) E2 Reset Phone E3 Reset Phone E4 Some Data (2*param=00..03,..,90..93) E5 Check Screen (2*param) E6 Some Data (2*param=00..99) UnKnown commands: (dunno what they do but this is what they say...) 22 Param (2*param) 29 Done (6*param) 2B Error (8*param) 2C Done (4*param) 2D Param (6*param) 2E Param 30 Error (16*param) 31 Error 32 Error 34 Error 35 Error (7*param) 37 Param (>100*param) 39 Done (4*param) 3B Done 60 Error (42*param) 62 Done (6*param) 64 Done (2*param) 65 Done (2*param) 66 Done (2*param) 69 Done (6*param) 72 Param (6*param) 74 Error (6*param) 77 Error (6*param) 78 Done (2*param) 80 Done 81 Done 82 Done 84 Done (2*param) 87 Done 88 Done 8C Done (2*param) 8D Done (4*param) 8F Done 90 Done 92 Error halts (2*param) 98 Error 9A Error 9B Error 9E Error A0 Done (2*param) A1 Done A2 Done (12*param) AB Done AC Done AD Done E0 Done (4*param) E1 Done (6*param) E7 Error E9 Param EB Done (2*param) EC Done (12*param) ED Done EE Done (8*param) EF Error (2*param) 1st. Technique: 904059 Menu - Enter Test Mode Yes 1F - Enter Mode Yes 86 - Speaker On Yes 83???? - Set Channel (?001..?31F) Yes 3D - Signal Level Yes 3F - Exit 2nd. Technique: 904059 Menu - Enter Test Mode Yes 1F - Enter Mode Yes 86 - Speaker On Yes 3C???? - Set Channel (0001..1023) Yes 3D - Signal Level Yes 3F - Exit (0..9=0..9 *=A; #=B; clr=C; menu=D; no=E; rcl=F). press Yes, at the @ enter the command. some of the commands have parameters of different lenght. if one parameter doesnt work try another. Ericsson A1018s (UN)LOCKING YOUR ERICSSON A1018s TO SPECIFIC NETWORK : A way to (un)lock your cell phone on to the network: 1. Press : <**< 2. Then on the display appear and give you two choices: Lock to Network ? and Lock to Network subset? 3. Enter the NCK number (code is provided by the SP) 4. You have 5 attemps to do this 5. Then your cell phone will work 'only' with the network Ericsson 218/337 To view IMEI number *#06# To view Software Version enter -> * <- <- * <- * CLR (Use with Care) To activate operator lock <- * * <- (This locks the phone to one carriers SIM card - Use with lots of care) Press Yes to lock and No to notlock. You can also use the codes below to undo this function. USE AT OWN RISK I have tested the function Lock to SP... At least on the 337 there's a submenu: Enter SPCK-code. There are 5 attempts, which is showed (05 attempts). At final attempt the phone beeps as a warning, 'this is the final try', when entering the menu... Wrong code exits the menu, so you are not stuck in something... When you have tried to enter the code (wrong) all five times, the menu is deactivated, and you'll get: 'Not allowed' when entering <-**<- A "secret test mode" can be accessed on the GH337. There seems to be two methods: > * < < * > * displays software version, such as 940810 1310 > * < < * < * displays software version, such as 951024 1054 After entering this mode, the < and > keys scroll through a menu. There seems to be different menus for different versions of software. Software version number are apparently a date and time stamp. 940810 1310 version commands: TEXT CHECK - shows 254 messages in current language INIT EEPROM MMI - resents NVRAM settings (User Settings). Other, probably more recent version: FLASH - will restart the phone, to the point of entering PIN numbers.You can't kill a 337 when pressing YES while it says "FLASH?", you must connect it to 5/12 volts first to be able to erase the flash-memory. 1-ROW TEXTS - scroll through 174 single line text messages with < and > n-ROW-TEXTS - scroll through full-screen messages with < and > 950626 1405 version commands: CXC (number) - The Application software's "product number". The GH337/GF337 is always "CXC 125 005" PRG - Indication for Programming Ericsson 368 Try these Codes on your DH-368 phone: 1) Power on. 2) Press 904059 + 'MENU' 3) 'TEST SET' display ... 4) Press 'YES' will display @ then press 1 'RCL' will turn light off and you will see 'DONE' 5) Press 'YES' will display @ then press 86 'RCL' display 'DONE' also you will hear static... You can just enter the channel number (up to 1023) by pressing 'Yes' 3 'CLR' XXXX - channel number to enter a channel directly. You can also see the signal level on channel by pressing 3 'MENU'. You can see the ESN number by pressing 'YES' 1 'RCL' 96 in HEX format. 6) Press 3 to exit, now you phone will power down and power up again. You can install the phone number into the phone by pressing 923885 + 'MENU' Ericsson GA628 *#06# for checking the IMEI (International Mobile Equipment Identity) *#0000# to reset the phones menu-language to English. *#103# then YES Time and date will be shown. >*<<*<* for checking the firmware revision information (software release) >*<<*<*> 1-row text strings. if pressing yes you can check the phones text programming in currently selected language. (298 entries) >*<<*<*>> n-row text strings. if pressing yes you can check the phones text programming in currently selected language. (160 entries?) Software UPDATED / NEW The phone should display something similar to this: CXC125065 - Cell phone's internalproduct code. PRG - Firmware revision - software version (date & time stamp). 970715 1515 LASTEST Version is: <990401> Fixes: ??? Software update, how? I have been asked a lot about how to update the software in cellular phones. The easiest thing to do is to go to the nearest Ericsson dealer and make him do it for you. Just remember that it is supposed to be free (a receipt is requiet) so don't let him tell you anything else! Service Provider Lock The Service Provider (SP) Lock menu is used to lock the cell phone to the SP's SIM card. Once the cell phone is locked to a specific operator, if one inserts a SIM card from a different operator the phone will refuse to accept it! The cell phone will however accept another SIM card from the same operator. To activate/deactivate this lock one needs a special secret code that is not available to the end user. (not even to you... or is it ? in case please let me know!) Here is how to activate the menu: <**< Lock to Network? if pressing yes you have 5 attempts to enter NCK. <**<< Lock to Network subset? if pressing yes you have 5 attempts to enter NSCK. Warning: Your phone can be locked to a service provider FOREVER by doing this! If an invalid code is entered all five times, the menu will exit and be deactivated! Any further attempt to activate the NCK/NSCK lock Menu will result in the response "Not allowed"! However the NCK/NSCK lock can be recover through a direct clearing in the EEPROM. Tips and Info Shortcut for Last Dialed call menu... If you for some reason don't want to enter the 'Last Dialed calls menu' by using the 'YES' key you can use the following key stroke instead: First '0' then '#'. Bat. level indicator when turned OFF... When the phone is turned off and the phone is not changing - the bat. level can be seen for a short period of time by pressing the 'NO' key quick once (it has to be quick!) and then wait for about 2 sec. The bat. level will now be shown in the display at its normal position. Access menu without Sim card ... To access to the menu in your phone without having a card inside do the following: type **04*0000*0000*0000# When display say "Wrong Pin" press NO and you have access to the all menus: Info, Access, Settings, Calculator, Clock, Keylock On?, Mail, Phone book. NOTE if you try this on your phone may stop at Keylock On? menu and you?ll have to take your battery out to turn the phone on again. Alarm Clock Menu.. Go to MissedCall Empty the list Press the -> key for a second or two The option Menu size turns up Choose 'yes' and go from there. An alarm clock turned up too but it never rang. I think this was because there is no clock in the phone. Free phone calls using the GA628.. NB! This trick has only been reported working on PREPAID GSM CARDS and in some countries and with some sw versions. The prepaid GSM SIM CARD is a kind of "SIM card" which only has a sertant amount of credit on it (like a normal phonebox telecard)... if it can be traced? - I don't know... Well..here's the trick you dial the no. normally and press YES. While "connecting" is shown on the screen, the following procedure should be carried out: Press CLR then 0 then # and then NO (twice) so as to switch OFF the phone. You can then still speak on the phone while it is switched off but the SIM card does not record your calls which will lead to FREE phone calls in some countries.. we hope!! Another variant of the code .. Make a Call, while the phone says Connecting type 083# (the position 83 must be empty! ), when phone says Pos Emtpy, press the NO key and turn off the phone. If you can make the call with the phone turned off you will face a problem when you need to hang up the phone...the only way for you to do that is remove the battery...??? Ericsson GF768 Tips & Tricks Edit Greetings Tip. 1. Go to the Keylock menu. 2. Set lock to Auto. 3. Press YES then hold the left arrow untill the Greetings menu appears. GF788 menu in your GF768 phone! (1) 1. Go to the EDIT MENU and press YES. 2. Type the number "2" and press YES. 3. In "NAME" HOLD DOWN the "2" key untill the number "2" apperars. Press YES. 4. Press YES again (to save any position) then QUICKLY press and hold left arrow (<) untill "SIZE" appears in the display. 5.Press YES and choose "Full size". You now have the GF788 menu! NB. Confirmed working on version 970716 and 980318. GF788 menu in your GF768 phone! (2) 1.Go to MissedCall 2. Empty the list 3. Press the -> key for a second or two 4. The option Menu size turns up 5. Choose 'yes' and go from there NB. Confirmed working on version 990122. GF788 menu in your GF768 phone! (3) 1. Go and set the ring volume and press yes. 2. When 'STORED' is displayed - keep the right button -> pressed until 'Extended Menu' is displayed. 3. Select "Activate" the menus and you now have lots of extra features NB. Confirmed working on version 980910 Software Lastest Firmaware Lastest Firmaware version: 990317 Ericsson GF788 *#06# for checking the IMEI (International Mobile Equipment Identity) >*<<*<* for checking the firmware revision information (software release) >*<<*<*> 1-row text strings. if pressing yes you can check the phones text programming in currently selected language. (298 entries) >*<<*<*>> n-row text strings. if pressing yes you can check the phones text programming in currently selected language. (160 entries?) Software The phone should display something similar to this: CXC125065 - Cell phone's internalproduct code. PRG - Firmware revision - software version (date & time stamp). 970715 1515 LASTEST Version is: <971128> Fixes: ??? Software update, how? I have been asked a lot about how to update the software in cellular phones. The easiest thing to do is to go to the nearest Ericsson dealer and make him do it for you. Just remember that it is supposed to be free (a receipt is requiet) so don't let him tell you anything else! Service Provider Lock The Service Provider (SP) Lock menu is used to lock the cell phone to the SP's SIM card. Once the cell phone is locked to a specific operator, if one inserts a SIM card from a different operator the phone will refuse to accept it! The cell phone will however accept another SIM card from the same operator. To activate/deactivate this lock one needs a special secret code that is not available to the end user. (not even to you... or is it ? in case please let me know!) Here is how to activate the menu: <**< Lock to Network? if pressing yes you have 5 attempts to enter NCK. <**<< Lock to Network subset? if pressing yes you have 5 attempts to enter NSCK. Warning: Your phone can be locked to a service provider FOREVER by doing this! If an invalid code is entered all five times, the menu will exit and be deactivated! Any further attempt to activate the NCK/NSCK lock Menu will result in the response "Not allowed"! However the NCK/NSCK lock can be recover through a direct clearing in the EEPROM. Tips and Info Shortcut for Last Dialed call menu... If you for some reason don't want to enter the 'Last Dialed calls menu' by using the 'YES' key you can use the following key stroke instead: First '0' then '#'. Bat. level indicator when turned OFF... When the gh688 is turned off and the phone is not changing - the bat. level can be seen for a short period of time by pressing the 'NO' key quick once (it has to be quick!) and then wait for about 2 sec. The bat. level will now be shown in the display at its normal position. Access menu without Sim card ... To access to the menu in your phone without having a card inside do the following: type **04*0000*0000*0000# When display say "Wrong Pin" press NO and you have access to the all menus: Info, Access, Settings, Calculator, Clock, Keylock On?, Mail, Phone book. NOTE if you try this on the GH688 your phone may stop at Keylock On? menu and you?ll have to take your battery out to turn the phone on again. Free phone calls using the GF788.. NB! This trick has only been reported working on PREPAID GSM CARDS and in some countries and with some sw versions. The prepaid GSM SIM CARD is a kind of "SIM card" which only has a sertant amount of credit on it (like a normal phonebox telecard)... if it can be traced? - I don't know... Well..here's the trick you dial the no. normally and press YES. While "connecting" is shown on the screen, the following procedure should be carried out: Press CLR then 0 then # and then NO (twice) so as to switch OFF the phone. You can then still speak on the phone while it is switched off but the SIM card does not record your calls which will lead to FREE phone calls in some countries.. we hope!! Another variant of the code .. Make a Call, while the phone says Connecting type 083# (the position 83 must be empty! ), when phone says Pos Emtpy, press the NO key and turn off the phone. If you can make the call with the phone turned off you will face a problem when you need to hang up the phone...the only way for you to do that is remove the battery...??? (Please tell me otherwise!!) Pin Outs Bottom view, keyboard up, counting from the left: 01 Out Audio from Mobile Station 02 In Audio to Mobile Station 03 In External Analog Audio Accessory Sense. Connect to GND to enable external mike and speaker 04 - Audio Signal Ground, 0V reference 05 In Portable Handsfree. 06 Out Music Mute (to mute e.g. the car radio) High when calling. 07 In Flash Memory Voltage and Service Voltage. Phone enters debugmode when tied to +5V at power-up. 08 Out Logic Reference, Status On. Sources over 100mA. 09 Out Data from Mobile Station. Debug messages appear here at 112KBaud when in debug mode. 10 GND Digital Ground and DC return 11 In Data to Mobile Station 12 I/O DC positive for battery charging (in)/DC for extenal accessory powering (out) All signals seem to be at 5V logic. Most debug messages are text. Like "CB ok!" etc. Debug messages are trailed by 0x0A, 0x0D. Power-up means removal of battery, reconnection of battery, depressure of "NO". A portable handsfree kit is connected as follows: Portable Handsfree (directly connected to pins 01, 02, 04): 01 Earphone: 16 Ohm 02 Microphone: <= 2 kOhm 05 to be connected to 04 (GND) Ericsson GH688 *#06# for checking the IMEI (International Mobile Equipment Identity) *#0000# to reset the phones menu-language to English. >*<<*<* for checking the firmware revision information (software release) >*<<*<*> 1-row text strings. if pressing yes you can check the phones text programming in currently selected language. (298 entries) >*<<*<*>> n-row text strings. if pressing yes you can check the phones text programming in currently selected language. (160 entries?) Software The phone should display something similar to this: CXC125065 - Cell phone's internalproduct code. PRG - Firmware revision - software version (date & time stamp). 970715 1515 LASTEST Version is: <980114> Fixes: ??? Fixes in Software version<971009> After receiving an SMS the prompt >>Message read?<< stayed on the screen until you pressed YES or NO. This new software eliminated this "feature" and when you receive an SMS >>Message read?<< stays on the screen only for a few seconds then it changes into an envelope. Fixes in Software version <970905> (and Ericsson 788 - software version 970716) The error is described as "MS unable to find HPLMN if 30 or more competitor ARFCN+s have greater signal strength than the HPLMN." In other words: if there are 30 or more channels belonging to other carriers which are stronger than the customer's home network, the phone will not be able to find the customer's home network. Fixes in Software version <970715> - The bug of the missing arrow on display when all diverting active. - Key lock key on display turned around , like in manual. (???) - An updated GSM operators' list. - Better and more solid reception. - Changing problem when turned OFF. Software update, how? I have been asked a lot about how to update the software in cellular phones. The easiest thing to do is to go to the nearest Ericsson dealer and make him do it for you. Just remember that it is supposed to be free (a receipt is requiet) so don't let him tell you anything else! Service Provider Lock The Service Provider (SP) Lock menu is used to lock the cell phone to the SP's SIM card. Once the cell phone is locked to a specific operator, if one inserts a SIM card from a different operator the phone will refuse to accept it! The cell phone will however accept another SIM card from the same operator. To activate/deactivate this lock one needs a special secret code that is not available to the end user. (not even to you... or is it ? in case please let me know!) Here is how to activate the menu: <**< Lock to Network? if pressing yes you have 5 attempts to enter NCK. <**<< Lock to Network subset? if pressing yes you have 5 attempts to enter NSCK. Warning: Your phone can be locked to a service provider FOREVER by doing this! If an invalid code is entered all five times, the menu will exit and be deactivated! Any further attempt to activate the NCK/NSCK lock Menu will result in the response "Not allowed"! However the NCK/NSCK lock can be recover through a direct clearing in the EEPROM. Tips and Info UPDATED / NEW Shortcut for Last Dialed call menu... If you for some reason don't want to enter the 'Last Dialed calls menu' by using the 'YES' key you can use the following key stroke instead: First '0' then '#'. Bat. level indicator when turned OFF... When the gh688 is turned off and the phone is not changing - the bat. level can be seen for a short period of time by pressing the 'NO' key quick once (it has to be quick!) and then wait for about 2 sec. The bat. level will now be shown in the display at its normal position. Access menu without Sim card ... To access to the menu in your phone without having a card inside do the following: type **04*0000*0000*0000# When display say "Wrong Pin" press NO and you have access to the all menus: Info, Access, Settings, Calculator, Clock, Keylock On?, Mail, Phone book. NOTE if you try this on the GH688 your phone may stop at Keylock On? menu and you?ll have to take your battery out to turn the phone on again. Full Network Name... You can see the Full Network Name by doing the following: Go to the network menu, when the phone displays the networks available (in 'Select net' and 'Edit list' menu) you can press * and you will see the full name. Full Operator List... You can view the full operator list by doing the following: Go to the 'Edit list' menu under 'networks'. The phone say 'please wait' (searching for other networks). When finished, Press the < key once, then YES twice. Now the phone displays the full list. Browse through the list with the < > keys. Monitor mod on Ericsson GH688.. How to enable net monitor on Ericson 688..(Let me know from you if your try this.. Haven't got a 688 anymore ;( ) 1. Remove SIM from phone 2. Dial 112, press YES, hear something, 3. Dial 112YESNO 4. Press <(left arrow) before SETTINGS 5. Then YES, <(left arrow), then u will see NM on? 6. press YES Free phone calls using the GH688.. NB! This trick has only been reported working on PREPAID GSM CARDS and in some countries and with some sw versions. The prepaid GSM SIM CARD is a kind of "SIM card" which only has a sertant amount of credit on it (like a normal phonebox telecard)... if it can be traced? - I don't know... Well..here's the trick you dial the no. normally and press YES. While "connecting" is shown on the screen, the following procedure should be carried out: Press CLR then 0 then # and then NO (twice) so as to switch OFF the phone. You can then still speak on the phone while it is switched off but the SIM card does not record your calls which will lead to FREE phone calls in some countries.. we hope!! Another variant of the code .. Make a Call, while the phone says Connecting type 083# (the position 83 must be empty! ), when phone says Pos Emtpy, press the NO key and turn off the phone. If you can make the call with the phone turned off you will face a problem when you need to hang up the phone...the only way for you to do that is remove the battery...??? (Please tell me otherwise!!) Pin Outs Bottom view, keyboard up, counting from the left: 01 Out Audio from Mobile Station 02 In Audio to Mobile Station 03 In External Analog Audio Accessory Sense. Connect to GND to enable external mike and speaker 04 - Audio Signal Ground, 0V reference 05 In Portable Handsfree. 06 Out Music Mute (to mute e.g. the car radio) High when calling. 07 In Flash Memory Voltage and Service Voltage. Phone enters debugmode when tied to +5V at power-up. 08 Out Logic Reference, Status On. Sources over 100mA. 09 Out Data from Mobile Station. Debug messages appear here at 112KBaud when in debug mode. 10 GND Digital Ground and DC return 11 In Data to Mobile Station 12 I/O DC positive for battery charging (in)/DC for extenal accessory powering (out) All signals seem to be at 5V logic. Most debug messages are text. Like "CB ok!" etc. Debug messages are trailed by 0x0A, 0x0D. Power-up means removal of battery, reconnection of battery, depressure of "NO". A portable handsfree kit is connected as follows: Portable Handsfree (directly connected to pins 01, 02, 04): 01 Earphone: 16 Ohm 02 Microphone: <= 2 kOhm 05 to be connected to 04 (GND) Ericsson SH888 *#06# for checking the IMEI (International Mobile Equipment Identity) >*<<*<* for checking the firmware revision information (software release) >*<<*<*> 1-row text strings. if pressing yes you can check the phones text programming in currently selected language. >*<<*<*>> n-row text strings. if pressing yes you can check the phones text programming in currently selected language. >*<<*<*>>> IR version info. if pressing yes you can check the phones IR device's driver version. Software The phone should display something similar to this: CXC125131- Cell phone's internalproduct code. PRG - Firmware revision 970715 1515 - software version (date & time stamp). LASTEST Version is: <991022> Older versions: <990614> CXC125131 PRG 990614 1714 IVER 980408 1035 PRGCXC125101 Software update, how? I have been asked a lot about how to update the software in cellular phones. The easiest thing to do is to go to the nearest Ericsson dealer and make him do it for you. Just remember that it is supposed to be free (a receipt is requiet) so don't let him tell you anything else! Service Provider Lock The Service Provider (SP) Lock menu is used to lock the cell phone to the SP's SIM card. Once the cell phone is locked to a specific operator, if one inserts a SIM card from a different operator the phone will refuse to accept it! The cell phone will however accept another SIM card from the same operator. To activate/deactivate this lock one needs a special secret code that is not available to the end user. (not even to you... or is it ? in case please let me know!) Here is how to activate the menu: <**< Lock to Network? if pressing yes you have 5 attempts to enter NCK. <**<< Lock to Network subset? if pressing yes you have 5 attempts to enter NSCK. Warning: Your phone can be locked to a service provider FOREVER by doing this! If an invalid code is entered all five times, the menu will exit and be deactivated! Any further attempt to activate the NCK/NSCK lock Menu will result in the response "Not allowed"! However the NCK/NSCK lock can be recover through a direct clearing in the EEPROM. Tips and Info Shortcut for Last Dialed call menu... If you for some reason don't want to enter the 'Last Dialed calls menu' by using the 'YES' key you can use the following key stroke instead: First '0' then '#'. Bat. level indicator when turned OFF... When the gh688 is turned off and the phone is not changing - the bat. level can be seen for a short period of time by pressing the 'NO' key quick once (it has to be quick!) and then wait for about 2 sec. The bat. level will now be shown in the display at its normal position. Access menu without Sim card ... To access to the menu in your phone without having a card inside do the following: type **04*0000*0000*0000# When display say "Wrong Pin" press NO and you have access to the all menus: Info, Access, Settings, Calculator, Clock, Keylock On?, Mail, Phone book. NOTE if you try this on the SH888 your phone may stop at Keylock On? menu and you?ll have to take your battery out to turn the phone on again. Ericsson T28 *#06# for checking the IMEI (International Mobile Equipment Identity) >*<<*<* for checking the firmware revision information (software release) >*<<*<*> 1-row text strings. if pressing yes you can check the phones text programming in currently selected language.) >*<<*<*>> n-row text strings. if pressing yes you can check the phones text programming in currently selected language. Software Type: CXC125115! The phone should display something similar to this: PRCXC125115 - Cell phone's internalproduct code. PRG - Firmware revision - software version (date & time stamp). 990718 1258 LASTEST Version is: <991022> Version <990831> Version <990718> Software update, how? I have been asked a lot about how to update the software in cellular phones. The easiest thing to do is to go to the nearest Ericsson dealer and make him do it for you. Just remember that it is supposed to be free (a receipt is requiet) so don't let him tell you anything else! Service Provider Lock The Service Provider (SP) Lock menu is used to lock the cell phone to the SP's SIM card. Once the cell phone is locked to a specific operator, if one inserts a SIM card from a different operator the phone will refuse to accept it! The cell phone will however accept another SIM card from the same operator. To activate/deactivate this lock one needs a special secret code that is not available to the end user. (not even to you... or is it ? in case please let me know!) Here is how to activate the menu: <**< Lock to Network? if pressing yes you have 5 attempts to enter NCK. <**<< Lock to Network subset? if pressing yes you have 5 attempts to enter NSCK. Warning: Your phone can be locked to a service provider FOREVER by doing this! If an invalid code is entered all five times, the menu will exit and be deactivated! Any further attempt to activate the NCK/NSCK lock Menu will result in the response "Not allowed"! However the NCK/NSCK lock can be recover through a direct clearing in the EEPROM. Tips and Info Shortcut for Last Dialed call menu... If you for some reason don't want to enter the 'Last Dialed calls menu' by using the 'YES' key you can use the following key stroke instead: First '0' then '#'. Ericsson v3688 Dual Band To view IMEI (International Mobile Equipment Identity) number enter *#06# Enhanced Full Rate Codec (EFR): To Enable EFR press [][][] 119 [] 1 [] OK. To Disable EFR press [][][] 119 [] 0 [] OK NOTE: Nothing appears on Screen LG ic-300W menu +9 , enter Service code (default = 000000) - programming mode press STO for a few seconds, 2539** , wait until you will see a massage press STO and enter "A Key". --- A Key Motorola StarTac 130 **05* Block Code **052* PIN2 Code Motorola 3688 Dual Band To view IMEI (International Mobile Equipment Identity) number enter *#06# Enhanced Full Rate Codec (EFR): To Enable EFR press [][][] 119 [] 1 [] OK. To Disable EFR press [][][] 119 [] 0 [] OK Motorola StarTac 6500 #program# Nam Editing [fnc]**testmode[sto] Enter Test Mode Motorola 7500, 7820 Activate RBS (Note: pause means the * key held in until box appears) To activate RBS type: [pause] [pause] [pause] 1 1 3 [pause] 1 [pause] [ok] You now have to press the [MENU] and scroll to the 'Eng Field Options' function with the keys, and enable it. De-activate RBS To de-activate RBS type: [pause] [pause] [pause] 1 1 3 [pause] 0 [pause] [ok] This only works with some versions of software. Please report to me what versions work and which doesn't. These countries has been reported working: d460: IT 6200 Flare: UK (Orange), AU 7500: IT (model: F16 HW: 5.2 SW: 2.1) 8200: ES, AU, NL, BE 8400: IT, NL 8700: AU, IT, SG, DE, ES, ZA What's the use of RBS: Get Distance From Base Station - Place a call, when it is answered, press [MENU] until 'Eng Field Option' is displayed, press [OK], select 'Active Cell', press [OK], press [MENU] until 'Time Adv xxx' appears, where xxx is a number. Multiply this number by 550, and the result is the distance from the RBS (Radio Base Station), in meters. Get Signal Quality - press [MENU] until 'Eng Field Option' is displayed, press [OK], select 'Active Cell', press [OK], press [MENU] until 'C1' appears. This is the signal quality. If it becomes negative for longer than 5 seconds, a new cell is selected. Motorola StarTac 7760 [fnc](SvcCode)(SvcCode)0[rcl] (default SvcCode=000000) Nam Programming 74663#1[fnc][fnc] Nam1 Programming Mode 79743[fnc][fnc] Enhanced Prefered Scanning [fnc][fnc]00**testmode[sto] Enter Test Mode (commands) 2539[sto] A-Key Motorola 8400, 8700 Activate RBS (Note: pause means the * key held in until box appears) To activate RBS type: [pause] [pause] [pause] 1 1 3 [pause] 1 [pause] [ok] You now have to press the [MENU] and scroll to the 'Eng Field Options' function with the keys, and enable it. De-activate RBS To de-activate RBS type: [pause] [pause] [pause] 1 1 3 [pause] 0 [pause] [ok] This only works with some versions of software. Please report to me what versions work and which doesn't. These countries has been reported working: d460: IT 6200 Flare: UK (Orange), AU 7500: IT (model: F16 HW: 5.2 SW: 2.1) 8200: ES, AU, NL, BE 8400: IT, NL 8700: AU, IT, SG, DE, ES, ZA What's the use of RBS: Get Distance From Base Station - Place a call, when it is answered, press [MENU] until 'Eng Field Option' is displayed, press [OK], select 'Active Cell', press [OK], press [MENU] until 'Time Adv xxx' appears, where xxx is a number. Multiply this number by 550, and the result is the distance from the RBS (Radio Base Station), in meters. Get Signal Quality - press [MENU] until 'Eng Field Option' is displayed, press [OK], select 'Active Cell', press [OK], press [MENU] until 'C1' appears. This is the signal quality. If it becomes negative for longer than 5 seconds, a new cell is selected. Motorola D160 **04* change pin number **05* request unblocking code *#06# displays phone IMEI number USE OF "SP UNLOCK CARD": 1 plug the SP card in 2 switch the phone on 3 it will take about 10 seconds till you see "clone" in the display 4 press 03# 5 wait 10 seconds 6 shut down the phone, now you can use your Motorola with each provider and the user lock and security code will be set on factory default. Tips and Tricks Motorola CD 160 Tip. Press menu and type one of these numbers and press OK: 11 = Status Review 13 = Available Networks 14 = Preferred Networks 22 = Select Keypad Tones 25 = Require SIM Card PIN 26 = Language Selection 32 = Repetitive Timer 33 = Single Alert Timer 34 = Set IN-Call Display 35 = Show Call Timers 36 = Show Call Charges 37 = Call Charge Settings 38 = Reset All Timers 43 = Reset All Timers 45 = Show Last Call 46 = Total For All Calls 47 = Lifetime Timer 51 = Change Unlock Code 52 = Master Reset 53 = Master Clear (Warning!! May result in deleting the Message Editor!!!) 54 = New Security Code 55 = Automatic Lock 63 = Battery Saving Mode Free call tip The trick can be done on cd160 and cd520 only: 1 Enter the phone number 2 Enter OK 3 Type *#06# 4 Press Button C 4 And finally press the button for power off. You should now be able to talk without being billed. Motorola d460/2500/6200 Activate RBS (Note: pause means the * key held in until box appears) To activate RBS type: [pause] [pause] [pause] 1 1 3 [pause] 1 [pause] [ok] You now have to press the [MENU] and scroll to the 'Eng Field Options' function with the keys, and enable it. De-activate RBS To de-activate RBS type: [pause] [pause] [pause] 1 1 3 [pause] 0 [pause] [ok] This only works with some versions of software. Please report to me what versions work and which doesn't. These countries has been reported working: d460: IT 6200 Flare: UK (Orange), AU 7500: IT (model: F16 HW: 5.2 SW: 2.1) 8200: ES, AU, NL, BE 8400: IT, NL 8700: AU, IT, SG, DE, ES, ZA What's the use of RBS: Get Distance From Base Station - Place a call, when it is answered, press [MENU] until 'Eng Field Option' is displayed, press [OK], select 'Active Cell', press [OK], press [MENU] until 'Time Adv xxx' appears, where xxx is a number. Multiply this number by 550, and the result is the distance from the RBS (Radio Base Station), in meters. Get Signal Quality - press [MENU] until 'Eng Field Option' is displayed, press [OK], select 'Active Cell', press [OK], press [MENU] until 'C1' appears. This is the signal quality. If it becomes negative for longer than 5 seconds, a new cell is selected. Motorola Сервисный режим AMPS/DAMPS/NAMPS телефонов В этой статье рассматриваются некоторые малоизвестные функции AMPS/NAMPS/DAMPS телефонов от Motorola, очень вероятно, что они могут понадобиться Вам в жизни. Заранее предупреждаем, что это сервисные настройки, и работать они могут не на всех телефонах, так что вы действуете на свой страх и риск. Проверено на TeleTac250, Profile300e. Итак: как сломать пароль (например Вы включаете чужой телефон, а он высвечивает Loc'd и стандартный пароль "123" не подходит): -включаем телефон -Видим Loc'd -жмем (FNC)-00**83786633-(STO)-# (вход в сервисный режим) - в итоге должны увидеть US' -жмем 55# - это настройки пользовательских параметров -жмем несколько раз * пока не увидим мигающие по очереди 7 и 000000, нули -это системный код который надо вводить при "легальной" смене пароля -жмем еще раз * и видим мигающие по очереди 8 (оно нам не надо) и трехзначное число - пароль, которое нам и нужно -теперь можно выключить телефон, а при включении набрать тот самый код из трех цифр!!! Общий сброс телефона, может понадобиться например при продаже телефона: -включаем телефон - жмем (FNC)-00**83786633-(STO)-# (вход в сервисный режим) - в итоге должны увидеть US' -давим 32# (нужно ждать пока не пикнет или не перезагрузится), -сбрасываются все таймеры, все телефонные книги, все настройки возвращаются в состояние по умолчанию; настройки вашего оператора ессно останутся (телефон резетится около минуты)... Motorola 5200, 7200, 7500 Pin-Out Motorola 5200, 7200, 7500 Pin-Out Numbered right to left, keypad up, battery down looking 1) Gnd 2) Pos 3) True data (TD) (input) 4) Complimentary data (CD) (input) 5) Return data (RD) (output) 6) Audio gnd 7) Audio out 8) Audio in Motorola 6200, 8200, 8400 Pin-Out Numbered left to right, keypad up, battery down 1) Audio Ground 2) V+ 3) True data (TD) (input) 4) Downlink - Complimentary data (CD) (input) 5) Uplink - Return data (RD) (output) 6) GND 7) Audio Out - on/off 8) Audio In 9) Manual Test - ??? 10) Battery Feedback 11) Antenna connector Tips and Tricks UPDATED / NEW Motorola 920/930: The 54# Tip: Type 1#, 2#........54# on the keypad (when you're not in the menu) to get the phone number used for with this key when speed dialing. Nec DB 2000 To see IMEI code type: *#06# To Reset to defaults type: *73738# (send?) To show Software version type : *#2820# SP Lock info: The procedure will show if your phone is locked. * # 3210 # (send?) for SIM lock info, type : *#8140# (send?) for Net lock info. SIM lock : *#4960 # (send?) - Inquiry * 4960 * password * password # (send?) to Lock #4960* password # (send?) to Unlock [password] is an 8 digits number] Net Lock: *#7320# (send?) - Inquiry * 7320 * password * password # (send?) to Lock. #7320* password # (send?) to Unlock. [password] is an 8 digits number] Net Lock 2: *#2220# (send?) - Inquiry * 2220 * password * password # (send?) to Lock #2220* password # (send?) to Unlock [password] is an 8 digits number] Subnet Lock: *#1110# (send?) - Inquiry * 1110 * password * password # (send?) to Lock #1110* password # (send?) to Unlock [password] is an 8 digits number] Nokia 1610/1611 *#06# for checking the IMEI (International Mobile Equipment Identity) *#170602112302# shows the SW version. Software Latest software version on Nokia 1610: v 5.15 (25.02.97) NHE-5NX - older version V 4.19 Latest software version on Nokia 1611: V 4.03 NHE-5SX Nokia 3110 *#06# for checking the IMEI (International Mobile Equipment Identity) *#7780# restores Factory Settings..(Memory, language, counters not included) *#3110# for checking the phone's software (SW) - called firmware revision information. *#746025625# [*#sim0clock#] to check if the Sim-Clock can be Stopped (Sim-clock-stop is a kind of standby mode which will save battery time) *#92702689# [*#war0anty#] Phone asks 'warranty code:' Press the following warranty code: 6232 (OK) : Displays the Month and Year of Manufacture (0997) 7332 (OK) : Displays the date of the last repairment - if found ('DATE NOT SAVED'...) 7832 (OK) : Displays (if found) the date where the phone was purchased ('DATE NOT SAVED'...) 9268 (OK) : Displays Serial Number 37832 (OK) : Set the Purchasing Date MMYY (Warning: You can only do this once - So be careful ...) 87267 (OK) : Transfers ALL phone numbers, pictures, sounds from one phone to another (eg. if broken) with 6110 u can transfer all data via IRport. (Confirm Transfer?)
|